Free Delivery on orders over £50

Free Delivery on orders over £50
Stomp Juicebox 110cc 12/10 Kids Youth Dirt BikeStomp Juicebox 110cc 12/10 Kids Youth Dirt Bike

Stomp Juicebox 110cc 12/10 Kids Youth Dirt Bike

  • Bullet proof Lifan 110 cc semi auto 4 speed all-up gearbox
  • Stealth ‘quiet’ exhaust system
  • light-weight steel spine frame
  • Conventional oil filled forks with strong steel triple clamps
  • Adjustable pre-load shock
  • Specially designed short length mx style swing arm
  • SDG hubs with 12/10″ steel rims
  • Quality off-road trail tyres
  • Composite fuel tank
  • Hi impact polypropylene plastics
  • Light-weight steel bars
  • Fold back brake lever
  • Hydraulic disk brakes with light weight rotors
  • Updated juicebox3 3-m Stomp Race graphics with Stomp race sponsor logos
  • Updated PRO foot pegs
  • Weight limit 9 stone
  • Seat height of 64cmColours and specification are subject to change without notice
    All pit bikes come with a 30 day parts only warranty.

 

PRICE:

£849.00

Only 1 left in stock

Elementor Single Product #882782
Description

Description

Stomp Juicebox 110cc 12/10 Kids Youth Dirt Bike

Welcome to the Generation 3 juicebox, this time specifically designed with those who are vertically challenged in mind. We have done away with all the fancy stuff and decided to give you exactly what you’ve been asking for: a small pit bike suitable for small people at a reasonable price. Although small, the Juicebox3 is perfectly formed and incredibly tough and durable.

Taking its geometry from the Honda CRF50, with low sculpted seat and 12/10 wheels, the JB3 sits at only 64 cm off the ground, perfect for any beginner or BIG KID alike (the JB3 will take a rider up to 9 stone). Updated with new Stomp Race graphics and new PRO footpegs.

Shipping

On every product page, you will find the delivery options available for that product. The options are as follows and will show delivery times for UK MAINLAND depending on which warehouse our stock is located in. You will be asked to make your selection in the checkout.

  • Standard (3-5 day delivery) UK Mainland
  • Northern Ireland – We are currently unable to ship parcels to Northern Ireland Due to complications caused by Brexit and import export procedures
  • Southern Ireland – We are currently unable to ship parcels to Southern Ireland Due to complications caused by Brexit and import export procedures
  • Highlands and Islands £40.00 Surcharge for all Large Ride On & Quad Bikes that are palatalised. Items under 25kg are included in free postage
  • Expedited (order by 2pm Monday – Thursday for next day delivery) when you choose this method of hipping.
  • Click and collect from our warehouse i currently unavailable due to covid restrictions
  • International – We Do Not Ship Internationally
UK MAINLAND COST DELIVERY TIME CARRIER
Standard Mainland UK Delivery FREE on orders over £50
£4.99 on orders up to £49.99
Delivery within 3-5 working days National Courier Signature Required & Trackable
 IV1 | IV2  Postcodes  £17.95  Delivery within 3-5 working Days  National Courier Signature Required & Trackable
Collect from our Warehouse NOT AVAILABLE SUSPENDED COVID-19

1.1 All goods are subject to availability.

1.2 Items ordered will be delivered as soon as possible in accordance with the requested delivery service. All delivery charges shown are for 3 to 5 day delivery of items in stock to U.K. mainland addresses only. If you require delivery to non-U.K. mainland address charges will vary depending upon the destination. Please contact us to discuss your requirements.

1.3 We will try to ensure that delivery is made within the estimated time scales.

1.4 For products listed on our Web Site outstanding orders can be cancelled at any time. In instances where payment has already been made, an alternative or refund in full for the item(s) concerned will be given.

1.5 You should check your order carefully when it is delivered to you. In the event of any goods delivered by us being damaged in transit, or failing to match the items ordered by you, then you should notify us promptly and within 48 hours to info@outsideplay.co.uk. We use independent couriers in order to deliver goods to you a quickly and efficiently as possible. We need to hear from you as soon as possible if you believe that your order has been damaged in transit so that we can investigate the matter with our couriers.

1.6 Any product with free delivery will only include the free service within mainland England. And the items will be sent by economy service and can take up to 7 working days during peak times.

1.7 Be aware by accepting our terms and conditions you give permission for your delivery to be left in a safe place/doorway/porch or received by a neighbour and something goes wrong, you will still be considered to have received the delivery. From this point on you take the risk and we will not take responsibility if its lost or stolen. Our contract with you is complete as soon as the parcel is delivered to your GPS location.

Stomp Build | Warranty

Stomp Build | Warranty

You have chosen wisely, the Pit Bike you have bought in order that you will enjoy your machine to the full.

Your bike has been supplied in a crate. This is NOT the same as buying a bike fully PDI’d (Pre Delivery Inspection) bike from a dealer. It is entirely your responsibility to ensure a qualified motorcycle mechanic puts your bike together correctly. Failure to do so will invalidate the warranty supplied with your bike.

STOMP WARRANTY

In order to qualify for this warranty you must fill in the supplied Proof Of Purchase, PDI & Warranty & post it to the supplied address. in your user manual

GUIDE FOR STOMP BIKE ASSEMBLY

This document is supplied only as a guide to a professional and may not be exhaustive. Each machine may require individual attention & therefore ONLY qualified persons should only carry out the following:

  • Remove Bike & all accessories from crate & inspect to ensure all necessary parts have been supplied correctly
  • Mount shock (where applicable)
  • Tighten lower fork bolt, reached from underside of forks.
  • Mount front wheel & ensure free rotation – check for potential bearing &/or brake drag Ensure all frame bolts are tight (use thread lock compound where necessary) – use locking wheel nut (supplied)
  • Check spokes and tighten if necessary
  • Loosen triple clamps around fork legs & set desired fork height. Use copper grease on triple clamp bolts to prevent damage to the alloy threads & then firmly tighten
  • Fit handlebars and clutch cable to clutch lever
  • Pump front brake lever until firm (bleed if necessary). Check front braking system for potential leaks or damage by pulling brake lever very hard several times. Visually inspect all joints for leaks & remedy where necessary. Spin wheel to ensure calliper is releasing from disk
  • Fit rear brake pedal where necessary & repeat procedure described for front brake
  • Check fluid levels, top up with DOT4 where necessary
  • Fit front mudguard using thread locking compound where required
  • Fit foot pegs
  • Loosen rear wheel & adjust chain tension. Find tightest point in chain by spinning rear wheel, there should 15mm up & 15mm down at the longest section of chain with rider sat on bike. Ensure chain runs true & is on top of chain roller. Ensure chain does not foul on rear chain guide (use shims/washer to space if necessary)
  • Working from front to rear, ensure all nuts & bolts are tight. Where no nyloc nuts or spring washers are present, ensure thread-locking compound has been used. If none has been used during factory assembly, remove nut or bolt, apply locking compound & re-tighten. Pay particular attention to the following critical safety areas: Wheel nuts, brake calliper bolts (thread lock), Top & rear engine bolts (frame must be hard tight against the engine, use thread lock), chain tensioners, rear shock bolts, triple clamp bolts (yokes), Handlebars, brake/ clutch/throttle, swing-arm, front & rear sprocket
  • Check all engine hardware is tight, (including but not exclusive): flywheel, inlet manifold, exhaust bolts,

Adjust tappets. Set engine to TDC (ONLY rotate engine anticlockwise) & check cam timing alignment (cam sprocket/cylinder head – adjust is necessary), remove tappet covers & adjust tappet clearances : inlet ~0.15mm – exhaust ~0.20mm

  • Fully ensure nothing is touching the exhaust system. On oil cooled models, ensure the oil cooler pipes do not touch the exhaust manifold
  • that the heat protection springs are located on the correct part of the pipe in order that should they touch the exhaust the heat will not damage them.
  • Ensure all cables pipes & wiring are away from moving components such as the wheels, use cable ties where necessary Carb –SS140 – set needle height on second notch from bottom for UK conditions. 110/125/150 engines normally do not need adjustment
  • Fuel bike & check for fuel leaks

Check oil level with bike in upright position using dipstick. Top up with 10W 40 semi synthetic oil, if necessary

  • Adjust tension for both clutch & throttle cables
  • Ensure wheel spokes are tight & wheels run true
  • Start engine & warm up (using choke if necessary). Set idle speed so engine ticks over comfortably without stalling or racing

(bearing in mind that the pads will need to bed in prior to optimum performance)

2 HOUR SERVICE

  • Drain oil & replace with Putoline DX4 semi synthetic 10w 40 4-stroke engine oil
  • Check all nuts & bolts & tighten where necessary (use PDI data as reference)
  • Check flywheel nut
  • Check wheel spokes (especially rear wheel drive side) & tighten where necessary
  • Re-Adjust throttle cable & clutch cable if required
  • Re-tension chain
  • Check wheel bearings for any sign of wear of free-play
  • Check brake calliper operation & brake pad wear
  • Check spark plug gap ~0.6mm-0.7mm
  • Check tyre pressures

RIDING TIPS FOR LONG ENGINE LIFE – IMPORTANT

  • Do not over rev your engine as you may cause damage to valves. This is particularly applicable where an inner rotor kit is used. Under load the engine is capable of revving into major valve bounce that can cause permanent damage to your engine. If you feel the power dropping every 10 hours use.
  • Do not stamp through the gears – always use the clutch.
  • If you miss a gear do NOT stamp into gear from high engine revs.
  • Do not drop your clutch heavily, or slip it unnecessarily.
  • Do not allow your air filter to fill with fuel – this can occur by incorrect float height setting – see above, or the bike falling onto its side.
  • If the engine back-fires while the air filter is filled with fuel, it may ignite – check air filter regularly while riding.
STOMP PROBLEM SOLVING
  • Exhaust Glows Red (fast tick over) – Carburetion too lean, richen mixture via raising needle
  • Engine misfires at mid to high engine speed, open throttle – Mixture too rich, drop needle
  • Engine Pops & bangs on over-run – mixture too rich, drop needle
  • Engine kicks back hard whilst starting – Ignition too advanced, or mixture too lean
  • Weak Spark – Pick-up coils too far from rotor (where inner rotor kit fitted) or bad earth
  • No spark – Either poor earth or faulty Rotor Coils/CDI/Coil/Lead/Cap/Plug – use moving coil multimeter to diagnose
  • Fuel leaks from overflow – Floats set incorrectly or blocked by debris or sticking
  • Engine runs fine, but then starts to misfire – faulty rotor coils/CDI/Coil/Plug
  • Rattles from engine – Tappets set incorrectly
  • Engine will not tick over when warm – tappets set incorrectly
  • Engine will not return to idle & races – sticking throttle cable
STOMP CORRECT JETTING

Take out the spark plug and check the electrode; the colour should be golden brown. If it is white, the engine is running too lean (not enough fuel). If it is black (sooty colour) it is too rich (too much fuel). If it is white & black, the engine is VERY lean & causing misfire, which you should be able to detect whilst riding. As your jets are close to what they should be for the UK, minor alterations can be made by

To add more fuel, raise the needle one notch. This is achieved by removing the carb from the engine, removing the throttle slide, removing the needle & adjusting the position of the circlip. Conversely, if you need to reduce the amount of fuel, drop the needle one notch. Re-assemble the carb & continue testing, remembering to check the colour of your spark plug.

Once you have achieved the correct full load fuelling, you can set the idle mixture screw. The 140 & 150 engines like to run very rich at idle, this way you get a clean progression from idle jet to main jet. To achieve a richer mixture, turn the air screw (next to filter) clockwise. Idle speed may need to be adjusted at same time to keep engine running.

STORAGE.

  • It is advisable to fully service and lubricate the bike prior to leaving the bike unused/unattended for any length of time.
  • It is advisable to fully drain the tank and carb of fuel prior to leaving the bike unused/unattended for any length of time.
Shop
Wishlist
0 items Cart

Shopping cart

close
Scroll To Top